sec_sequence.push_back( eSecCommand(eSecCommand::IF_VOLTAGE_GOTO, compare) );
compare.steps = +3;
sec_sequence.push_back( eSecCommand(eSecCommand::SET_VOLTAGE, compare.voltage) );
- // voltage was disabled..so we wait a longer time .. for normal switches 200ms should be enough
- sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 200) );
+ // voltage was disabled..so we wait a longer time .. for normal switches 750ms should be enough
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 750) );
for (int seq_repeat = 0; seq_repeat < (di_param.m_seq_repeat?2:1); ++seq_repeat)
{
if ( send_mask & 2 )
++loops;
- for ( int i=0; i < di_param.m_repeats; ++i )
- loops *= 2;
+ loops <<= di_param.m_repeats;
for ( int i = 0; i < loops;) // fill commands...
{
cmd=0x38;
if (cmd)
{
- static int delay = (120 - 54) / 2; // standard says 100msek between two repeated commands
+ int delay = di_param.m_repeats ? (120 - 54) / 2 : 120; // standard says 100msek between two repeated commands
sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, delay) );
diseqc.data[2]=cmd;
diseqc.data[3]=(cmd==0x38) ? csw : ucsw;
if ( RotorCmd != -1 && RotorCmd != lastRotorCmd )
{
eSecCommand::pair compare;
- compare.voltage = iDVBFrontend::voltageOff;
- compare.steps = +4;
- // the next is a check if voltage is switched off.. then we first set a voltage :)
- // else we set voltage after all diseqc stuff..
- sec_sequence.push_back( eSecCommand(eSecCommand::IF_NOT_VOLTAGE_GOTO, compare) );
-
- if (rotor_param.m_inputpower_parameters.m_use)
- sec_sequence.push_back( eSecCommand(eSecCommand::SET_VOLTAGE, VOLTAGE(13)) ); // in normal mode start turning with 13V
- else
- sec_sequence.push_back( eSecCommand(eSecCommand::SET_VOLTAGE, VOLTAGE(18)) ); // turn always with 18V
+ if (!send_mask)
+ {
+ compare.voltage = iDVBFrontend::voltageOff;
+ compare.steps = +4;
+ // the next is a check if voltage is switched off.. then we first set a voltage :)
+ // else we set voltage after all diseqc stuff..
+ sec_sequence.push_back( eSecCommand(eSecCommand::IF_NOT_VOLTAGE_GOTO, compare) );
- // voltage was disabled..so we wait a longer time ..
- sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 500) );
- sec_sequence.push_back( eSecCommand(eSecCommand::GOTO, +7) ); // no need to send stop rotor cmd
+ if (rotor_param.m_inputpower_parameters.m_use)
+ sec_sequence.push_back( eSecCommand(eSecCommand::SET_VOLTAGE, VOLTAGE(13)) ); // in normal mode start turning with 13V
+ else
+ sec_sequence.push_back( eSecCommand(eSecCommand::SET_VOLTAGE, VOLTAGE(18)) ); // turn always with 18V
- if (send_mask)
- sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 750) ); // wait 750ms after send switch cmd
+ // voltage was disabled..so we wait a longer time ..
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 750) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::GOTO, +8) ); // no need to send stop rotor cmd and recheck voltage
+ }
else
- sec_sequence.push_back( eSecCommand(eSecCommand::GOTO, +1) );
+ {
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 750) ); // wait 750ms after send switch cmd
+ sec_sequence.push_back( eSecCommand(eSecCommand::GOTO, +8) ); // no need to send stop rotor cmd and recheck voltage
+ }
eDVBDiseqcCommand diseqc;
diseqc.len = 3;