+
+ int RotorCmd=-1;
+ bool useGotoXX = false;
+ if ( di_param.m_diseqc_mode == eDVBSatelliteDiseqcParameters::V1_2 )
+ {
+ if (depend_satpos_mode || linked)
+ // in this both modes we dont really turn the rotor.... but in canTune we need the satpos
+ frontend.setData(6, sat.orbital_position);
+ else
+ {
+ if (sw_param.m_rotorPosNum) // we have stored rotor pos?
+ RotorCmd=sw_param.m_rotorPosNum;
+ else // we must calc gotoxx cmd
+ {
+ eDebug("Entry for %d,%d? not in Rotor Table found... i try gotoXX?", sat.orbital_position / 10, sat.orbital_position % 10 );
+ useGotoXX = true;
+
+ double SatLon = abs(sat.orbital_position)/10.00,
+ SiteLat = rotor_param.m_gotoxx_parameters.m_latitude,
+ SiteLon = rotor_param.m_gotoxx_parameters.m_longitude;
+
+ if ( rotor_param.m_gotoxx_parameters.m_la_direction == eDVBSatelliteRotorParameters::SOUTH )
+ SiteLat = -SiteLat;
+
+ if ( rotor_param.m_gotoxx_parameters.m_lo_direction == eDVBSatelliteRotorParameters::WEST )
+ SiteLon = 360 - SiteLon;
+
+ eDebug("siteLatitude = %lf, siteLongitude = %lf, %lf degrees", SiteLat, SiteLon, SatLon );
+ double satHourAngle =
+ calcSatHourangle( SatLon, SiteLat, SiteLon );
+ eDebug("PolarmountHourAngle=%lf", satHourAngle );
+
+ static int gotoXTable[10] =
+ { 0x00, 0x02, 0x03, 0x05, 0x06, 0x08, 0x0A, 0x0B, 0x0D, 0x0E };
+
+ if (SiteLat >= 0) // Northern Hemisphere
+ {
+ int tmp=(int)round( fabs( 180 - satHourAngle ) * 10.0 );
+ RotorCmd = (tmp/10)*0x10 + gotoXTable[ tmp % 10 ];
+
+ if (satHourAngle < 180) // the east
+ RotorCmd |= 0xE000;
+ else // west
+ RotorCmd |= 0xD000;
+ }
+ else // Southern Hemisphere
+ {
+ if (satHourAngle < 180) // the east
+ {
+ int tmp=(int)round( fabs( satHourAngle ) * 10.0 );
+ RotorCmd = (tmp/10)*0x10 + gotoXTable[ tmp % 10 ];
+ RotorCmd |= 0xD000;
+ }
+ else // west
+ {
+ int tmp=(int)round( fabs( 360 - satHourAngle ) * 10.0 );
+ RotorCmd = (tmp/10)*0x10 + gotoXTable[ tmp % 10 ];
+ RotorCmd |= 0xE000;
+ }
+ }
+ eDebug("RotorCmd = %04x", RotorCmd);
+ }
+ }
+ }
+
+ if ( send_mask )
+ {
+ sec_sequence.push_back( eSecCommand(eSecCommand::SET_TONE, iDVBFrontend::toneOff) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 15) );
+ eSecCommand::pair compare;
+ compare.voltage = iDVBFrontend::voltageOff;
+ compare.steps = +4;
+ // the next is a check if voltage is switched off.. then we first set a voltage :)
+ // else we set voltage after all diseqc stuff..
+ sec_sequence.push_back( eSecCommand(eSecCommand::IF_NOT_VOLTAGE_GOTO, compare) );
+
+ if ( RotorCmd != -1 && RotorCmd != lastRotorCmd )
+ // TODO .. add handling for turning rotor without measure inputpower
+ compare.voltage = VOLTAGE(18);
+ else
+ compare.voltage = voltage;
+
+ // voltage already correct ?
+ sec_sequence.push_back( eSecCommand(eSecCommand::IF_VOLTAGE_GOTO, compare) );
+ compare.steps = +3;
+ sec_sequence.push_back( eSecCommand(eSecCommand::SET_VOLTAGE, compare.voltage) );
+ // voltage was disabled..so we wait a longer time .. for normal switches 200ms should be enough
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 200) );
+
+ for (int seq_repeat = 0; seq_repeat < (di_param.m_seq_repeat?2:1); ++seq_repeat)
+ {
+ if ( send_mask & 4 )
+ {
+ sec_sequence.push_back( eSecCommand(eSecCommand::SEND_TONEBURST, di_param.m_toneburst_param) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 50) );
+ }
+
+ int loops=0;
+
+ if ( send_mask & 1 )
+ ++loops;
+ if ( send_mask & 2 )
+ ++loops;
+
+ for ( int i=0; i < di_param.m_repeats; ++i )
+ loops *= 2;
+
+ for ( int i = 0; i < loops;) // fill commands...
+ {
+ eDVBDiseqcCommand diseqc;
+ diseqc.len = 4;
+ diseqc.data[0] = i ? 0xE1 : 0xE0;
+ diseqc.data[1] = 0x10;
+ if ( (send_mask & 2) && (di_param.m_command_order & 4) )
+ {
+ diseqc.data[2] = 0x39;
+ diseqc.data[3] = ucsw;
+ }
+ else if ( send_mask & 1 )
+ {
+ diseqc.data[2] = 0x38;
+ diseqc.data[3] = csw;
+ }
+ else
+ {
+ diseqc.data[2] = 0x00;
+ diseqc.data[3] = 0x00;
+ }
+ sec_sequence.push_back( eSecCommand(eSecCommand::SEND_DISEQC, diseqc) );
+
+ i++;
+ if ( i < loops )
+ {
+ int cmd=0;
+ if (diseqc.data[2] == 0x38 && (send_mask & 2))
+ cmd=0x39;
+ else if (diseqc.data[2] == 0x39 && (send_mask & 1))
+ cmd=0x38;
+ if (cmd)
+ {
+ static int delay = (120 - 54) / 2; // standard says 100msek between two repeated commands
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, delay) );
+ diseqc.data[2]=cmd;
+ diseqc.data[3]=(cmd==0x38) ? csw : ucsw;
+ sec_sequence.push_back( eSecCommand(eSecCommand::SEND_DISEQC, diseqc) );
+ ++i;
+ if ( i < loops )
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, delay ) );
+ else
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 50) );
+ }
+ else // delay 120msek when no command is in repeat gap
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 120) );
+ }
+ else
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 50) );
+ }
+
+ if ( send_mask & 8 ) // toneburst at end of sequence
+ {
+ sec_sequence.push_back( eSecCommand(eSecCommand::SEND_TONEBURST, di_param.m_toneburst_param) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 50) );
+ }
+ }
+ }
+
+ if ( RotorCmd != -1 && RotorCmd != lastRotorCmd )
+ {
+ eSecCommand::pair compare;
+ compare.voltage = iDVBFrontend::voltageOff;
+ compare.steps = +4;
+ // the next is a check if voltage is switched off.. then we first set a voltage :)
+ // else we set voltage after all diseqc stuff..
+ sec_sequence.push_back( eSecCommand(eSecCommand::IF_NOT_VOLTAGE_GOTO, compare) );
+
+ // TODO .. add handling for turning rotor without measure inputpower
+ sec_sequence.push_back( eSecCommand(eSecCommand::SET_VOLTAGE, VOLTAGE(18)) );
+ // voltage was disabled..so we wait a longer time ..
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 500) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::GOTO, +7) ); // no need to send stop rotor cmd
+
+ if (send_mask)
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 750) ); // wait 750ms after send switch cmd
+ else
+ sec_sequence.push_back( eSecCommand(eSecCommand::GOTO, +1) );
+
+ eDVBDiseqcCommand diseqc;
+ diseqc.len = 3;
+ diseqc.data[0] = 0xE0;
+ diseqc.data[1] = 0x31; // positioner
+ diseqc.data[2] = 0x60; // stop
+ sec_sequence.push_back( eSecCommand(eSecCommand::IF_ROTORPOS_VALID_GOTO, +5) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SEND_DISEQC, diseqc) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 50) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SEND_DISEQC, diseqc) );
+ // wait 300msec after send rotor stop cmd
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 300) );
+
+ diseqc.data[0] = 0xE0;
+ diseqc.data[1] = 0x31; // positioner
+ if ( useGotoXX )
+ {
+ diseqc.len = 5;
+ diseqc.data[2] = 0x6E; // drive to angular position
+ diseqc.data[3] = ((RotorCmd & 0xFF00) / 0x100);
+ diseqc.data[4] = RotorCmd & 0xFF;
+ }
+ else
+ {
+ diseqc.len = 4;
+ diseqc.data[2] = 0x6B; // goto stored sat position
+ diseqc.data[3] = RotorCmd;
+ diseqc.data[4] = 0x00;
+ }
+
+ if ( rotor_param.m_inputpower_parameters.m_use )
+ { // use measure rotor input power to detect rotor state
+ eSecCommand::rotor cmd;
+ eSecCommand::pair compare;
+ compare.voltage = VOLTAGE(18);
+ compare.steps = +2;
+ sec_sequence.push_back( eSecCommand(eSecCommand::IF_VOLTAGE_GOTO, compare) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SET_VOLTAGE, compare.voltage) );
+// measure idle power values
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 200) ); // wait 200msec after voltage change
+ sec_sequence.push_back( eSecCommand(eSecCommand::MEASURE_IDLE_INPUTPOWER, 1) );
+ compare.voltage = 1;
+ compare.steps = -2;
+ sec_sequence.push_back( eSecCommand(eSecCommand::IF_MEASURE_IDLE_WAS_NOT_OK_GOTO, compare) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SET_VOLTAGE, VOLTAGE(13)) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 200) ); // wait 200msec before measure
+ sec_sequence.push_back( eSecCommand(eSecCommand::MEASURE_IDLE_INPUTPOWER, 0) );
+ compare.voltage = 0;
+ sec_sequence.push_back( eSecCommand(eSecCommand::IF_MEASURE_IDLE_WAS_NOT_OK_GOTO, compare) );
+////////////////////////////
+ sec_sequence.push_back( eSecCommand(eSecCommand::SET_POWER_LIMITING_MODE, eSecCommand::modeStatic) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SET_ROTOR_DISEQC_RETRYS, 2) ); // 2 retries
+ sec_sequence.push_back( eSecCommand(eSecCommand::INVALIDATE_CURRENT_ROTORPARMS) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SEND_DISEQC, diseqc) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SET_TIMEOUT, 40) ); // 2 seconds rotor start timout
+// rotor start loop
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 50) ); // 50msec delay
+ sec_sequence.push_back( eSecCommand(eSecCommand::MEASURE_RUNNING_INPUTPOWER) );
+ cmd.direction=1; // check for running rotor
+ cmd.deltaA=rotor_param.m_inputpower_parameters.m_delta;
+ cmd.steps=+5;
+ cmd.okcount=0;
+ sec_sequence.push_back( eSecCommand(eSecCommand::IF_INPUTPOWER_DELTA_GOTO, cmd ) ); // check if rotor has started
+ sec_sequence.push_back( eSecCommand(eSecCommand::IF_TIMEOUT_GOTO, +2 ) ); // timeout .. we assume now the rotor is already at the correct position
+ sec_sequence.push_back( eSecCommand(eSecCommand::GOTO, -4) ); // goto loop start
+ sec_sequence.push_back( eSecCommand(eSecCommand::IF_NO_MORE_ROTOR_DISEQC_RETRYS_GOTO, +9 ) ); // timeout .. we assume now the rotor is already at the correct position
+ sec_sequence.push_back( eSecCommand(eSecCommand::GOTO, -8) ); // goto loop start
+////////////////////
+ sec_sequence.push_back( eSecCommand(eSecCommand::SET_TIMEOUT, 2400) ); // 2 minutes running timeout
+ sec_sequence.push_back( eSecCommand(eSecCommand::SET_VOLTAGE, VOLTAGE(18)) );
+// rotor running loop
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 50) ); // wait 50msec
+ sec_sequence.push_back( eSecCommand(eSecCommand::MEASURE_RUNNING_INPUTPOWER) );
+ cmd.direction=0; // check for stopped rotor
+ cmd.steps=+3;
+ sec_sequence.push_back( eSecCommand(eSecCommand::IF_INPUTPOWER_DELTA_GOTO, cmd ) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::IF_TIMEOUT_GOTO, +3 ) ); // timeout ? this should never happen
+ sec_sequence.push_back( eSecCommand(eSecCommand::GOTO, -4) ); // running loop start
+/////////////////////
+ sec_sequence.push_back( eSecCommand(eSecCommand::UPDATE_CURRENT_ROTORPARAMS) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SET_POWER_LIMITING_MODE, eSecCommand::modeDynamic) );
+ frontend.setData(3, RotorCmd);
+ frontend.setData(4, sat.orbital_position);
+ }
+ else
+ eFatal("rotor turning without inputpowermeasure not implemented yet");
+ }
+ }
+ else
+ csw = band;
+
+ frontend.setData(0, csw);
+ frontend.setData(1, ucsw);
+ frontend.setData(2, di_param.m_toneburst_param);
+
+ if ( linked )
+ return 0;
+
+ eSecCommand::pair compare;
+ compare.voltage = voltage;
+ compare.steps = +3;
+ sec_sequence.push_back( eSecCommand(eSecCommand::IF_VOLTAGE_GOTO, compare) ); // voltage already correct ?
+ sec_sequence.push_back( eSecCommand(eSecCommand::SET_VOLTAGE, voltage) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 10) );
+
+ sec_sequence.push_back( eSecCommand(eSecCommand::SET_TONE, tone) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 15) );
+
+ frontend.setSecSequence(sec_sequence);
+
+ return 0;
+ }
+ }
+
+ eDebug("found no useable satellite configuration for orbital position (%d)", sat.orbital_position );
+ return -1;
+}
+
+RESULT eDVBSatelliteEquipmentControl::clear()
+{
+ for (int i=0; i < m_lnbidx; ++i)
+ {
+ m_lnbs[i].m_satellites.clear();
+ m_lnbs[i].tuner_mask = 0;
+ }
+ m_lnbidx=-1;
+
+// clear linked tuner configuration
+ for (eSmartPtrList<eDVBRegisteredFrontend>::iterator it(m_avail_frontends.begin()); it != m_avail_frontends.end(); ++it)
+ it->m_frontend->setData(7, -1);
+
+ return 0;
+}
+
+// helper function for setTunerLinked and setTunerDepends
+RESULT eDVBSatelliteEquipmentControl::setDependencyPointers( int tu1, int tu2, int dest_data_byte )
+{
+ if (tu1 == tu2)
+ return -1;
+
+ eDVBRegisteredFrontend *p1=NULL, *p2=NULL;
+
+ int cnt=0;
+ for (eSmartPtrList<eDVBRegisteredFrontend>::iterator it(m_avail_frontends.begin()); it != m_avail_frontends.end(); ++it, ++cnt)
+ {
+ if (cnt == tu1)
+ p1 = *it;
+ else if (cnt == tu2)
+ p2 = *it;
+ }
+ if (p1 && p2)
+ {
+ p1->m_frontend->setData(dest_data_byte, (int)p2); // this is evil..
+ p2->m_frontend->setData(dest_data_byte, (int)p1);
+ return 0;
+ }
+ return -1;
+}
+
+/* LNB Specific Parameters */
+RESULT eDVBSatelliteEquipmentControl::addLNB()
+{
+ if ( m_lnbidx < (int)(sizeof(m_lnbs) / sizeof(eDVBSatelliteLNBParameters)))
+ m_curSat=m_lnbs[++m_lnbidx].m_satellites.end();