eDVBSatelliteEquipmentControl *eDVBSatelliteEquipmentControl::instance;
+int eDVBSatelliteEquipmentControl::m_params[MAX_PARAMS];
+/*
+ defaults are set in python lib/python/Components/NimManager.py
+ in InitSecParams function via setParam call
+*/
+
+void eDVBSatelliteEquipmentControl::setParam(int param, int value)
+{
+ if (param >= 0 && param < MAX_PARAMS)
+ m_params[param]=value;
+}
+
eDVBSatelliteEquipmentControl::eDVBSatelliteEquipmentControl(eSmartPtrList<eDVBRegisteredFrontend> &avail_frontends)
:m_lnbidx(-1), m_curSat(m_lnbs[0].m_satellites.end()), m_avail_frontends(avail_frontends), m_rotorMoving(false)
{
setRotorPosNum(1); // stored pos 1
}
+static void checkLinkedParams(int direction, int &linked_ptr, int &ret, const eDVBFrontendParametersSatellite &sat, int csw, int ucsw, int toneburst, bool diseqc, bool rotor)
+{
+ eDVBRegisteredFrontend *linked_fe = (eDVBRegisteredFrontend*) linked_ptr;
+ int oRotorPos = -1;
+ linked_fe->m_frontend->getData(eDVBFrontend::ROTOR_POS, oRotorPos);
+ if (linked_fe->m_inuse)
+ {
+ int ocsw = -1,
+ oucsw = -1,
+ oToneburst = -1;
+ linked_fe->m_frontend->getData(eDVBFrontend::CSW, ocsw);
+ linked_fe->m_frontend->getData(eDVBFrontend::UCSW, oucsw);
+ linked_fe->m_frontend->getData(eDVBFrontend::TONEBURST, oToneburst);
+#if 0
+ eDebug("compare csw %02x == lcsw %02x",
+ csw, ocsw);
+ if ( diseqc )
+ eDebug("compare ucsw %02x == lucsw %02x\ncompare toneburst %02x == oToneburst %02x",
+ ucsw, oucsw, toneburst, oToneburst);
+ if ( rotor )
+ eDebug("compare pos %d == current pos %d",
+ sat.orbital_position, oRotorPos);
+#endif
+ if ( (csw != ocsw) ||
+ ( diseqc && (ucsw != oucsw || toneburst != oToneburst) ) ||
+ ( rotor && oRotorPos != sat.orbital_position ) )
+ {
+// eDebug("can not tune this transponder with linked tuner in use!!");
+ ret=0;
+ }
+// else
+// eDebug("OK .. can tune this transponder with linked tuner in use :)");
+ }
+ else if (rotor && oRotorPos != -1)
+ {
+ ret -= abs(oRotorPos-sat.orbital_position);
+// eDebug("decrement rotor pos for linked tuner!!");
+ }
+ linked_fe->m_frontend->getData(direction, linked_ptr);
+}
+
int eDVBSatelliteEquipmentControl::canTune(const eDVBFrontendParametersSatellite &sat, iDVBFrontend *fe, int frontend_id )
{
int ret=0, satcount=0;
for (int idx=0; idx <= m_lnbidx; ++idx )
{
+ bool rotor=false;
eDVBSatelliteLNBParameters &lnb_param = m_lnbs[idx];
if ( lnb_param.tuner_mask & frontend_id ) // lnb for correct tuner?
{
if (!(sat.polarisation & eDVBFrontendParametersSatellite::Polarisation::Vertical))
band |= 2;
- bool rotor=false;
bool diseqc=false;
if (di_param.m_diseqc_mode >= eDVBSatelliteDiseqcParameters::V1_0)
ret = 15000;
}
- while (linked_prev_ptr != -1) // check for linked tuners..
- {
- eDVBRegisteredFrontend *linked_fe = (eDVBRegisteredFrontend*) linked_prev_ptr;
- if (linked_fe->m_inuse)
- {
- int ocsw = -1,
- oucsw = -1,
- oToneburst = -1,
- oRotorPos = -1;
- linked_fe->m_frontend->getData(eDVBFrontend::CSW, ocsw);
- linked_fe->m_frontend->getData(eDVBFrontend::UCSW, oucsw);
- linked_fe->m_frontend->getData(eDVBFrontend::TONEBURST, oToneburst);
- linked_fe->m_frontend->getData(eDVBFrontend::ROTOR_POS, oRotorPos);
-#if 0
- eDebug("compare csw %02x == lcsw %02x",
- csw, ocsw);
- if ( diseqc )
- eDebug("compare ucsw %02x == lucsw %02x\ncompare toneburst %02x == oToneburst %02x",
- ucsw, oucsw, toneburst, oToneburst);
- if ( rotor )
- eDebug("compare pos %d == current pos %d",
- sat.orbital_position, oRotorPos);
-#endif
- if ( (csw != ocsw) ||
- ( diseqc && (ucsw != oucsw || toneburst != oToneburst) ) ||
- ( rotor && oRotorPos != sat.orbital_position ) )
- {
-// eDebug("can not tune this transponder with linked tuner in use!!");
- ret=0;
- break;
- }
-// else
-// eDebug("OK .. can tune this transponder with linked tuner in use :)");
- }
- linked_fe->m_frontend->getData(eDVBFrontend::LINKED_PREV_PTR, linked_prev_ptr);
- }
+ while (ret && linked_prev_ptr != -1) // check for linked tuners..
+ checkLinkedParams(eDVBFrontend::LINKED_PREV_PTR, linked_prev_ptr, ret, sat, csw, ucsw, toneburst, diseqc, rotor);
- if (ret)
- while (linked_next_ptr != -1) // check for linked tuners..
- {
- eDVBRegisteredFrontend *linked_fe = (eDVBRegisteredFrontend*) linked_next_ptr;
- if (linked_fe->m_inuse)
- {
- int ocsw = -1,
- oucsw = -1,
- oToneburst = -1,
- oRotorPos = -1;
- linked_fe->m_frontend->getData(eDVBFrontend::CSW, ocsw);
- linked_fe->m_frontend->getData(eDVBFrontend::UCSW, oucsw);
- linked_fe->m_frontend->getData(eDVBFrontend::TONEBURST, oToneburst);
- linked_fe->m_frontend->getData(eDVBFrontend::ROTOR_POS, oRotorPos);
-#if 0
- eDebug("compare csw %02x == lcsw %02x",
- csw, ocsw);
- if ( diseqc )
- eDebug("compare ucsw %02x == lucsw %02x\ncompare toneburst %02x == oToneburst %02x",
- ucsw, oucsw, toneburst, oToneburst);
- if ( rotor )
- eDebug("compare pos %d == current pos %d",
- sat.orbital_position, oRotorPos);
-#endif
- if ( (csw != ocsw) ||
- ( diseqc && (ucsw != oucsw || toneburst != oToneburst) ) ||
- ( rotor && oRotorPos != sat.orbital_position ) )
- {
-// eDebug("can not tune this transponder with linked tuner in use!!");
- ret=0;
- break;
- }
-// else
-// eDebug("OK .. can tune this transponder with linked tuner in use :)");
- }
- linked_fe->m_frontend->getData(eDVBFrontend::LINKED_NEXT_PTR, linked_next_ptr);
- }
+ while (ret && linked_next_ptr != -1) // check for linked tuners..
+ checkLinkedParams(eDVBFrontend::LINKED_NEXT_PTR, linked_next_ptr, ret, sat, csw, ucsw, toneburst, diseqc, rotor);
if (ret)
if (satpos_depends_ptr != -1)
RotorCmd = (tmp/10)*0x10 + gotoXTable[ tmp % 10 ];
RotorCmd |= 0xD000;
}
- else // west
+ else // west
{
int tmp=(int)round( fabs( 360 - satHourAngle ) * 10.0 );
RotorCmd = (tmp/10)*0x10 + gotoXTable[ tmp % 10 ];
if ( send_mask )
{
- sec_sequence.push_back( eSecCommand(eSecCommand::SET_TONE, iDVBFrontend::toneOff) );
- sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 15) );
eSecCommand::pair compare;
+ compare.steps = +3;
+ compare.tone = iDVBFrontend::toneOff;
+ sec_sequence.push_back( eSecCommand(eSecCommand::IF_TONE_GOTO, compare) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SET_TONE, iDVBFrontend::toneOff) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, m_params[DELAY_AFTER_CONT_TONE]) );
compare.voltage = iDVBFrontend::voltageOff;
- compare.steps = +4;
+ compare.steps = +3;
// the next is a check if voltage is switched off.. then we first set a voltage :)
// else we set voltage after all diseqc stuff..
sec_sequence.push_back( eSecCommand(eSecCommand::IF_NOT_VOLTAGE_GOTO, compare) );
if ( RotorCmd != -1 && RotorCmd != lastRotorCmd )
{
if (rotor_param.m_inputpower_parameters.m_use)
- compare.voltage = VOLTAGE(18); // in input power mode turn rotor always with 18V (fast)
+ compare.voltage = VOLTAGE(18); // in input power mode set 18V for measure input power
else
compare.voltage = VOLTAGE(13); // in normal mode start turning with 13V
}
else
compare.voltage = voltage;
- // voltage already correct ?
- sec_sequence.push_back( eSecCommand(eSecCommand::IF_VOLTAGE_GOTO, compare) );
- compare.steps = +3;
sec_sequence.push_back( eSecCommand(eSecCommand::SET_VOLTAGE, compare.voltage) );
- // voltage was disabled..so we wait a longer time .. for normal switches 750ms should be enough
- sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 750) );
+
+ // voltage was disabled..so we wait a longer time .. for normal switches 250ms should be enough
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, m_params[DELAY_AFTER_ENABLE_VOLTAGE_BEFORE_SWITCH_CMDS]) );
for (int seq_repeat = 0; seq_repeat < (di_param.m_seq_repeat?2:1); ++seq_repeat)
{
if ( send_mask & 4 )
{
sec_sequence.push_back( eSecCommand(eSecCommand::SEND_TONEBURST, di_param.m_toneburst_param) );
- sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 50) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, m_params[DELAY_AFTER_TONEBURST]) );
}
int loops=0;
cmd=0x39;
else if (diseqc.data[2] == 0x39 && (send_mask & 1))
cmd=0x38;
+ int tmp = m_params[DELAY_BETWEEN_DISEQC_REPEATS];
if (cmd)
{
- int delay = di_param.m_repeats ? (120 - 54) / 2 : 120; // standard says 100msek between two repeated commands
+ int delay = di_param.m_repeats ? (tmp - 54) / 2 : tmp; // standard says 100msek between two repeated commands
sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, delay) );
diseqc.data[2]=cmd;
diseqc.data[3]=(cmd==0x38) ? csw : ucsw;
if ( i < loops )
sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, delay ) );
else
- sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 50) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, m_params[DELAY_AFTER_LAST_DISEQC_CMD]) );
}
else // delay 120msek when no command is in repeat gap
- sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 120) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, tmp) );
}
else
- sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 50) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, m_params[DELAY_AFTER_LAST_DISEQC_CMD]) );
}
if ( send_mask & 8 ) // toneburst at end of sequence
{
sec_sequence.push_back( eSecCommand(eSecCommand::SEND_TONEBURST, di_param.m_toneburst_param) );
- sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 50) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, m_params[DELAY_AFTER_TONEBURST]) );
}
}
}
eSecCommand::pair compare;
if (!send_mask)
{
+ compare.steps = +3;
+ compare.tone = iDVBFrontend::toneOff;
+ sec_sequence.push_back( eSecCommand(eSecCommand::IF_TONE_GOTO, compare) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SET_TONE, iDVBFrontend::toneOff) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, m_params[DELAY_AFTER_CONT_TONE]) );
+
compare.voltage = iDVBFrontend::voltageOff;
compare.steps = +4;
// the next is a check if voltage is switched off.. then we first set a voltage :)
sec_sequence.push_back( eSecCommand(eSecCommand::IF_NOT_VOLTAGE_GOTO, compare) );
if (rotor_param.m_inputpower_parameters.m_use)
- sec_sequence.push_back( eSecCommand(eSecCommand::SET_VOLTAGE, VOLTAGE(13)) ); // in normal mode start turning with 13V
+ sec_sequence.push_back( eSecCommand(eSecCommand::SET_VOLTAGE, VOLTAGE(18)) ); // set 18V for measure input power
else
- sec_sequence.push_back( eSecCommand(eSecCommand::SET_VOLTAGE, VOLTAGE(18)) ); // turn always with 18V
+ sec_sequence.push_back( eSecCommand(eSecCommand::SET_VOLTAGE, VOLTAGE(13)) ); // in normal mode start turning with 13V
- // voltage was disabled..so we wait a longer time ..
- sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 750) );
- sec_sequence.push_back( eSecCommand(eSecCommand::GOTO, +8) ); // no need to send stop rotor cmd and recheck voltage
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, m_params[DELAY_AFTER_ENABLE_VOLTAGE_BEFORE_MOTOR_CMD]) ); // wait 750ms when voltage was disabled
+ sec_sequence.push_back( eSecCommand(eSecCommand::GOTO, +9) ); // no need to send stop rotor cmd and recheck voltage
}
else
- {
- sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 750) ); // wait 750ms after send switch cmd
- sec_sequence.push_back( eSecCommand(eSecCommand::GOTO, +8) ); // no need to send stop rotor cmd and recheck voltage
- }
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, m_params[DELAY_BETWEEN_SWITCH_AND_MOTOR_CMD]) ); // wait 700ms when diseqc changed
eDVBDiseqcCommand diseqc;
diseqc.len = 3;
sec_sequence.push_back( eSecCommand(eSecCommand::SEND_DISEQC, diseqc) );
sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 50) );
sec_sequence.push_back( eSecCommand(eSecCommand::SEND_DISEQC, diseqc) );
- // wait 300msec after send rotor stop cmd
- sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 300) );
+ // wait 150msec after send rotor stop cmd
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, m_params[DELAY_AFTER_MOTOR_STOP_CMD]) );
diseqc.data[0] = 0xE0;
diseqc.data[1] = 0x31; // positioner
eSecCommand::rotor cmd;
eSecCommand::pair compare;
compare.voltage = VOLTAGE(18);
- compare.steps = +2;
+ compare.steps = +3;
sec_sequence.push_back( eSecCommand(eSecCommand::IF_VOLTAGE_GOTO, compare) );
sec_sequence.push_back( eSecCommand(eSecCommand::SET_VOLTAGE, compare.voltage) );
// measure idle power values
- sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 200) ); // wait 200msec after voltage change
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, m_params[DELAY_AFTER_VOLTAGE_CHANGE_BEFORE_MEASURE_IDLE_INPUTPOWER]) ); // wait 150msec after voltage change
sec_sequence.push_back( eSecCommand(eSecCommand::MEASURE_IDLE_INPUTPOWER, 1) );
- compare.voltage = 1;
+ compare.val = 1;
compare.steps = -2;
sec_sequence.push_back( eSecCommand(eSecCommand::IF_MEASURE_IDLE_WAS_NOT_OK_GOTO, compare) );
sec_sequence.push_back( eSecCommand(eSecCommand::SET_VOLTAGE, VOLTAGE(13)) );
- sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 200) ); // wait 200msec before measure
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, m_params[DELAY_AFTER_VOLTAGE_CHANGE_BEFORE_MEASURE_IDLE_INPUTPOWER]) ); // wait 150msec before measure
sec_sequence.push_back( eSecCommand(eSecCommand::MEASURE_IDLE_INPUTPOWER, 0) );
- compare.voltage = 0;
+ compare.val = 0;
sec_sequence.push_back( eSecCommand(eSecCommand::IF_MEASURE_IDLE_WAS_NOT_OK_GOTO, compare) );
////////////////////////////
sec_sequence.push_back( eSecCommand(eSecCommand::SET_POWER_LIMITING_MODE, eSecCommand::modeStatic) );
- sec_sequence.push_back( eSecCommand(eSecCommand::SET_ROTOR_DISEQC_RETRYS, 2) ); // 2 retries
+ sec_sequence.push_back( eSecCommand(eSecCommand::SET_ROTOR_DISEQC_RETRYS, m_params[MOTOR_COMMAND_RETRIES]) ); // 2 retries
sec_sequence.push_back( eSecCommand(eSecCommand::INVALIDATE_CURRENT_ROTORPARMS) );
sec_sequence.push_back( eSecCommand(eSecCommand::SEND_DISEQC, diseqc) );
sec_sequence.push_back( eSecCommand(eSecCommand::SET_TIMEOUT, 40) ); // 2 seconds rotor start timout
sec_sequence.push_back( eSecCommand(eSecCommand::IF_INPUTPOWER_DELTA_GOTO, cmd ) ); // check if rotor has started
sec_sequence.push_back( eSecCommand(eSecCommand::IF_TIMEOUT_GOTO, +2 ) ); // timeout .. we assume now the rotor is already at the correct position
sec_sequence.push_back( eSecCommand(eSecCommand::GOTO, -4) ); // goto loop start
- sec_sequence.push_back( eSecCommand(eSecCommand::IF_NO_MORE_ROTOR_DISEQC_RETRYS_GOTO, +9 ) ); // timeout .. we assume now the rotor is already at the correct position
+ sec_sequence.push_back( eSecCommand(eSecCommand::IF_NO_MORE_ROTOR_DISEQC_RETRYS_GOTO, +10 ) ); // timeout .. we assume now the rotor is already at the correct position
sec_sequence.push_back( eSecCommand(eSecCommand::GOTO, -8) ); // goto loop start
////////////////////
- sec_sequence.push_back( eSecCommand(eSecCommand::SET_TIMEOUT, 2400) ); // 2 minutes running timeout
sec_sequence.push_back( eSecCommand(eSecCommand::SET_VOLTAGE, VOLTAGE(18)) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SET_POWER_LIMITING_MODE, eSecCommand::modeDynamic) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SET_TIMEOUT, m_params[MOTOR_RUNNING_TIMEOUT]*20) ); // 2 minutes running timeout
// rotor running loop
sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 50) ); // wait 50msec
sec_sequence.push_back( eSecCommand(eSecCommand::MEASURE_RUNNING_INPUTPOWER) );
cmd.direction=0; // check for stopped rotor
- cmd.steps=+3;
+ cmd.steps=+4;
sec_sequence.push_back( eSecCommand(eSecCommand::IF_INPUTPOWER_DELTA_GOTO, cmd ) );
- sec_sequence.push_back( eSecCommand(eSecCommand::IF_TIMEOUT_GOTO, +3 ) ); // timeout ? this should never happen
+ sec_sequence.push_back( eSecCommand(eSecCommand::IF_TIMEOUT_GOTO, +4 ) ); // timeout ? this should never happen
sec_sequence.push_back( eSecCommand(eSecCommand::GOTO, -4) ); // running loop start
/////////////////////
+ sec_sequence.push_back( eSecCommand(eSecCommand::SET_POWER_LIMITING_MODE, eSecCommand::modeDynamic) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::UPDATE_CURRENT_ROTORPARAMS) );
}
else
{ // use normal turning mode
eSecCommand::rotor cmd;
eSecCommand::pair compare;
compare.voltage = VOLTAGE(13);
- compare.steps = +2;
+ compare.steps = +3;
sec_sequence.push_back( eSecCommand(eSecCommand::IF_VOLTAGE_GOTO, compare) );
sec_sequence.push_back( eSecCommand(eSecCommand::SET_VOLTAGE, compare.voltage) );
- sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 200) ); // wait 200msec after voltage change
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, m_params[DELAY_AFTER_VOLTAGE_CHANGE_BEFORE_MOTOR_CMD]) ); // wait 150msec after voltage change
sec_sequence.push_back( eSecCommand(eSecCommand::SET_POWER_LIMITING_MODE, eSecCommand::modeStatic) );
sec_sequence.push_back( eSecCommand(eSecCommand::INVALIDATE_CURRENT_ROTORPARMS) );
sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 2000) ); // wait 2 second before set high voltage
sec_sequence.push_back( eSecCommand(eSecCommand::SET_VOLTAGE, voltage) );
+ compare.tone = tone;
+ sec_sequence.push_back( eSecCommand(eSecCommand::IF_TONE_GOTO, compare) );
sec_sequence.push_back( eSecCommand(eSecCommand::SET_TONE, tone) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, m_params[DELAY_AFTER_CONT_TONE]) );
sec_sequence.push_back( eSecCommand(eSecCommand::SET_FRONTEND) );
cmd.direction=1; // check for running rotor
cmd.deltaA=0;
cmd.steps=+3;
cmd.okcount=0;
-
- sec_sequence.push_back( eSecCommand(eSecCommand::SET_TIMEOUT, 480) ); // 2 minutes running timeout
+ sec_sequence.push_back( eSecCommand(eSecCommand::SET_TIMEOUT, m_params[MOTOR_RUNNING_TIMEOUT]*4) ); // 2 minutes running timeout
sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 250) ); // 250msec delay
sec_sequence.push_back( eSecCommand(eSecCommand::IF_TUNER_LOCKED_GOTO, cmd ) );
sec_sequence.push_back( eSecCommand(eSecCommand::IF_TIMEOUT_GOTO, +3 ) );
sec_sequence.push_back( eSecCommand(eSecCommand::GOTO, -3) ); // goto loop start
+ sec_sequence.push_back( eSecCommand(eSecCommand::UPDATE_CURRENT_ROTORPARAMS) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SET_POWER_LIMITING_MODE, eSecCommand::modeDynamic) );
}
- sec_sequence.push_back( eSecCommand(eSecCommand::UPDATE_CURRENT_ROTORPARAMS) );
- sec_sequence.push_back( eSecCommand(eSecCommand::SET_POWER_LIMITING_MODE, eSecCommand::modeDynamic) );
frontend.setData(eDVBFrontend::NEW_ROTOR_CMD, RotorCmd);
frontend.setData(eDVBFrontend::NEW_ROTOR_POS, sat.orbital_position);
}
compare.steps = +3;
sec_sequence.push_back( eSecCommand(eSecCommand::IF_VOLTAGE_GOTO, compare) ); // voltage already correct ?
sec_sequence.push_back( eSecCommand(eSecCommand::SET_VOLTAGE, voltage) );
- sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 10) );
-
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, m_params[DELAY_AFTER_FINAL_VOLTAGE_CHANGE]) );
+ compare.tone = tone;
+ sec_sequence.push_back( eSecCommand(eSecCommand::IF_TONE_GOTO, compare) );
sec_sequence.push_back( eSecCommand(eSecCommand::SET_TONE, tone) );
- sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 15) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, m_params[DELAY_AFTER_CONT_TONE]) );
}
if (doSetFrontend)
RESULT eDVBSatelliteEquipmentControl::setTunerLinked(int tu1, int tu2)
{
- if (tu1 == tu2)
- return -1;
-
- eDVBRegisteredFrontend *p1=NULL, *p2=NULL;
-
- int cnt=0;
- for (eSmartPtrList<eDVBRegisteredFrontend>::iterator it(m_avail_frontends.begin()); it != m_avail_frontends.end(); ++it, ++cnt)
- {
- if (cnt == tu1)
- p1 = *it;
- else if (cnt == tu2)
- p2 = *it;
- }
- if (p1 && p2)
+ if (tu1 != tu2)
{
- p1->m_frontend->setData(eDVBFrontend::LINKED_PREV_PTR, (int)p2);
- p2->m_frontend->setData(eDVBFrontend::LINKED_NEXT_PTR, (int)p1);
- return 0;
+ eDVBRegisteredFrontend *p1=NULL, *p2=NULL;
+
+ int cnt=0;
+ for (eSmartPtrList<eDVBRegisteredFrontend>::iterator it(m_avail_frontends.begin()); it != m_avail_frontends.end(); ++it, ++cnt)
+ {
+ if (cnt == tu1)
+ p1 = *it;
+ else if (cnt == tu2)
+ p2 = *it;
+ }
+ if (p1 && p2)
+ {
+ p1->m_frontend->setData(eDVBFrontend::LINKED_PREV_PTR, (int)p2);
+ p2->m_frontend->setData(eDVBFrontend::LINKED_NEXT_PTR, (int)p1);
+ return 0;
+ }
}
+ return -1;
}
RESULT eDVBSatelliteEquipmentControl::setTunerDepends(int tu1, int tu2)