if ( di_param.m_committed_cmd < eDVBSatelliteDiseqcParameters::SENDNO )
csw = 0xF0 | (csw << 2);
- csw |= band;
+ if (di_param.m_committed_cmd <= eDVBSatelliteDiseqcParameters::SENDNO)
+ csw |= band;
if ( di_param.m_diseqc_mode == eDVBSatelliteDiseqcParameters::V1_2 ) // ROTOR
{
rotor=true;
if ( curRotorPos == sat.orbital_position )
- ret=20;
+ ret=20; // rotor on correct orbpos = prio 20
else
- ret=10;
+ ret=10; // rotor must turn to correct orbpos = prio 10
}
+ else
+ ret = 30; // no rotor = prio 30
}
else
+ {
csw = band;
-
- if (!ret)
- ret=40;
+ ret = 40; // no diseqc = prio 40
+ }
if (linked_to != -1) // check for linked tuners..
{
// else
// eDebug("OK .. can tune this transponder satpos is correct :)");
}
+ if (ret)
+ {
+ static int lofs[] = { 3650000, 5150000, 9750000, 10600000 };
+ int lof = sat.frequency > lnb_param.m_lof_threshold ?
+ lnb_param.m_lof_hi : lnb_param.m_lof_lo;
+ int diff = 0x7FFFFFFF;
+ unsigned int num_lofs = sizeof(lofs) / sizeof(int);
+ int used_band = -1;
+ for (int i=0; i < num_lofs; ++i)
+ {
+ int lof_diff = abs(lof - lofs[i]);
+ if ( lof_diff < diff )
+ {
+ diff = lof_diff;
+ used_band = i;
+ }
+ }
+ if ( used_band != -1 )
+ {
+ if ( diff > 50000 )
+ {
+ eDebug("could not detect used lnb freq range .. disable range check !!!");
+ used_band = -1;
+ }
+ }
+ if ( used_band != -1 )
+ {
+ int range[2];
+ switch(used_band)
+ {
+ case 0: // s-band
+ range[0] = 2500000;
+ range[1] = 2700000;
+ break;
+ case 1: // c-band
+ range[0] = 3400000;
+ range[1] = 4200000;
+ break;
+ case 2: // ku-band low
+ range[0] = 10700000;
+ range[1] = 11750000;
+ break;
+ case 3: // ku-band high
+ range[0] = 11750000;
+ range[1] = 12750000;
+ break;
+ }
+ // check frequency in range ( +/- 75Mhz )
+ if ( (sat.frequency+75000) < range[0] )
+ ret=0;
+ if ( (sat.frequency-75000) > range[1] )
+ ret=0;
+ }
+ }
}
}
}
else
parm.FREQUENCY = sat.frequency - lnb_param.m_lof_lo;
+ parm.FREQUENCY = abs(parm.FREQUENCY);
+
if (sat.polarisation == eDVBFrontendParametersSatellite::Polarisation::Horizontal)
band |= 2;
if ( di_param.m_committed_cmd < eDVBSatelliteDiseqcParameters::SENDNO )
csw = 0xF0 | (csw << 2);
- csw |= band;
+ if (di_param.m_committed_cmd <= eDVBSatelliteDiseqcParameters::SENDNO)
+ csw |= band;
bool send_csw =
(di_param.m_committed_cmd != eDVBSatelliteDiseqcParameters::SENDNO);
}
if (changed_csw)
{
- if ( di_param.m_use_fast && (lastcsw & 0xF0) && ((csw / 4) == (lastcsw / 4)) )
+ if ( di_param.m_use_fast
+ && di_param.m_committed_cmd < eDVBSatelliteDiseqcParameters::SENDNO
+ && (lastcsw & 0xF0)
+ && ((csw / 4) == (lastcsw / 4)) )
eDebug("dont send committed cmd (fast diseqc)");
else
{
eDebug("");
#endif
- if ( send_mask )
- {
- sec_sequence.push_back( eSecCommand(eSecCommand::SET_TONE, iDVBFrontend::toneOff) );
- eSecCommand::pair compare;
- compare.voltage = voltage;
- compare.steps = +3;
- sec_sequence.push_back( eSecCommand(eSecCommand::IF_VOLTAGE_GOTO, compare) ); // voltage already correct ?
- sec_sequence.push_back( eSecCommand(eSecCommand::SET_VOLTAGE, voltage) );
- sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 50) );
- }
-
- for (int seq_repeat = 0; seq_repeat < (di_param.m_seq_repeat?2:1); ++seq_repeat)
- {
- if ( send_mask & 4 )
- {
- sec_sequence.push_back( eSecCommand(eSecCommand::SEND_TONEBURST, di_param.m_toneburst_param) );
- sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 50) );
- }
-
- int loops=0;
-
- if ( send_mask & 1 )
- ++loops;
- if ( send_mask & 2 )
- ++loops;
-
- for ( int i=0; i < di_param.m_repeats; ++i )
- loops *= 2;
-
- for ( int i = 0; i < loops;) // fill commands...
- {
- eDVBDiseqcCommand diseqc;
- diseqc.len = 4;
- diseqc.data[0] = i ? 0xE1 : 0xE0;
- diseqc.data[1] = 0x10;
- if ( (send_mask & 2) && (di_param.m_command_order & 4) )
- {
- diseqc.data[2] = 0x39;
- diseqc.data[3] = ucsw;
- }
- else if ( send_mask & 1 )
- {
- diseqc.data[2] = 0x38;
- diseqc.data[3] = csw;
- }
- else
- {
- diseqc.data[2] = 0x00;
- diseqc.data[3] = 0x00;
- }
- sec_sequence.push_back( eSecCommand(eSecCommand::SEND_DISEQC, diseqc) );
-
- i++;
- if ( i < loops )
- {
- int cmd=0;
- if (diseqc.data[2] == 0x38 && (send_mask & 2))
- cmd=0x39;
- else if (diseqc.data[2] == 0x39 && (send_mask & 1))
- cmd=0x38;
- if (cmd)
- {
- static int delay = (120 - 54) / 2; // standard says 100msek between two repeated commands
- sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, delay) );
- diseqc.data[2]=cmd;
- diseqc.data[3]=(cmd==0x38) ? csw : ucsw;
- sec_sequence.push_back( eSecCommand(eSecCommand::SEND_DISEQC, diseqc) );
- ++i;
- if ( i < loops )
- sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, delay ) );
- else
- sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 50) );
- }
- else // delay 120msek when no command is in repeat gap
- sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 120) );
- }
- else
- sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 50) );
- }
-
- if ( send_mask & 8 ) // toneburst at end of sequence
- {
- sec_sequence.push_back( eSecCommand(eSecCommand::SEND_TONEBURST, di_param.m_toneburst_param) );
- sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 50) );
- }
- }
-
+ int RotorCmd=-1;
+ bool useGotoXX = false;
if ( di_param.m_diseqc_mode == eDVBSatelliteDiseqcParameters::V1_2 )
{
if (depend_satpos_mode || linked)
frontend.setData(6, sat.orbital_position);
else
{
- int RotorCmd=0;
- bool useGotoXX = false;
-
if (sw_param.m_rotorPosNum) // we have stored rotor pos?
RotorCmd=sw_param.m_rotorPosNum;
else // we must calc gotoxx cmd
RotorCmd |= 0xD000;
}
else // west
- {
+ {
int tmp=(int)round( fabs( 360 - satHourAngle ) * 10.0 );
RotorCmd = (tmp/10)*0x10 + gotoXTable[ tmp % 10 ];
RotorCmd |= 0xE000;
}
eDebug("RotorCmd = %04x", RotorCmd);
}
- if ( RotorCmd != lastRotorCmd )
+ }
+ }
+
+ if ( send_mask )
+ {
+ sec_sequence.push_back( eSecCommand(eSecCommand::SET_TONE, iDVBFrontend::toneOff) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 15) );
+ eSecCommand::pair compare;
+ compare.voltage = iDVBFrontend::voltageOff;
+ compare.steps = +4;
+ // the next is a check if voltage is switched off.. then we first set a voltage :)
+ // else we set voltage after all diseqc stuff..
+ sec_sequence.push_back( eSecCommand(eSecCommand::IF_NOT_VOLTAGE_GOTO, compare) );
+
+ if ( RotorCmd != -1 && RotorCmd != lastRotorCmd )
+ // TODO .. add handling for turning rotor without measure inputpower
+ compare.voltage = VOLTAGE(18);
+ else
+ compare.voltage = voltage;
+
+ // voltage already correct ?
+ sec_sequence.push_back( eSecCommand(eSecCommand::IF_VOLTAGE_GOTO, compare) );
+ compare.steps = +3;
+ sec_sequence.push_back( eSecCommand(eSecCommand::SET_VOLTAGE, compare.voltage) );
+ // voltage was disabled..so we wait a longer time .. for normal switches 200ms should be enough
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 200) );
+
+ for (int seq_repeat = 0; seq_repeat < (di_param.m_seq_repeat?2:1); ++seq_repeat)
+ {
+ if ( send_mask & 4 )
+ {
+ sec_sequence.push_back( eSecCommand(eSecCommand::SEND_TONEBURST, di_param.m_toneburst_param) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 50) );
+ }
+
+ int loops=0;
+
+ if ( send_mask & 1 )
+ ++loops;
+ if ( send_mask & 2 )
+ ++loops;
+
+ for ( int i=0; i < di_param.m_repeats; ++i )
+ loops *= 2;
+
+ for ( int i = 0; i < loops;) // fill commands...
{
- if ( send_mask )
+ eDVBDiseqcCommand diseqc;
+ diseqc.len = 4;
+ diseqc.data[0] = i ? 0xE1 : 0xE0;
+ diseqc.data[1] = 0x10;
+ if ( (send_mask & 2) && (di_param.m_command_order & 4) )
{
- // override first voltage change
- *(++(++sec_sequence.begin()))=eSecCommand(eSecCommand::SET_VOLTAGE, VOLTAGE(13));
- // wait 1 second after first switch diseqc command
- sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 1000) );
+ diseqc.data[2] = 0x39;
+ diseqc.data[3] = ucsw;
}
- else // no other diseqc commands before
+ else if ( send_mask & 1 )
{
- sec_sequence.push_back( eSecCommand(eSecCommand::SET_TONE, iDVBFrontend::toneOff) );
- sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 15) ); // wait 15msec after tone change
- eSecCommand::pair compare;
- compare.voltage = voltage;
- compare.steps = +3;
- sec_sequence.push_back( eSecCommand(eSecCommand::IF_VOLTAGE_GOTO, compare) ); // voltage already correct ?
- sec_sequence.push_back( eSecCommand(eSecCommand::SET_VOLTAGE, VOLTAGE(13)) );
- sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 50) ); // wait 50msec after voltage change
+ diseqc.data[2] = 0x38;
+ diseqc.data[3] = csw;
}
-
- eDVBDiseqcCommand diseqc;
- diseqc.data[0] = 0xE0;
- diseqc.data[1] = 0x31; // positioner
- if ( useGotoXX )
+ else
{
- diseqc.len = 5;
- diseqc.data[2] = 0x6E; // drive to angular position
- diseqc.data[3] = ((RotorCmd & 0xFF00) / 0x100);
- diseqc.data[4] = RotorCmd & 0xFF;
+ diseqc.data[2] = 0x00;
+ diseqc.data[3] = 0x00;
}
- else
+ sec_sequence.push_back( eSecCommand(eSecCommand::SEND_DISEQC, diseqc) );
+
+ i++;
+ if ( i < loops )
{
- diseqc.len = 4;
- diseqc.data[2] = 0x6B; // goto stored sat position
- diseqc.data[3] = RotorCmd;
- diseqc.data[4] = 0x00;
+ int cmd=0;
+ if (diseqc.data[2] == 0x38 && (send_mask & 2))
+ cmd=0x39;
+ else if (diseqc.data[2] == 0x39 && (send_mask & 1))
+ cmd=0x38;
+ if (cmd)
+ {
+ static int delay = (120 - 54) / 2; // standard says 100msek between two repeated commands
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, delay) );
+ diseqc.data[2]=cmd;
+ diseqc.data[3]=(cmd==0x38) ? csw : ucsw;
+ sec_sequence.push_back( eSecCommand(eSecCommand::SEND_DISEQC, diseqc) );
+ ++i;
+ if ( i < loops )
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, delay ) );
+ else
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 50) );
+ }
+ else // delay 120msek when no command is in repeat gap
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 120) );
}
+ else
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 50) );
+ }
- if ( rotor_param.m_inputpower_parameters.m_use )
- { // use measure rotor input power to detect rotor state
- eSecCommand::rotor cmd;
+ if ( send_mask & 8 ) // toneburst at end of sequence
+ {
+ sec_sequence.push_back( eSecCommand(eSecCommand::SEND_TONEBURST, di_param.m_toneburst_param) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 50) );
+ }
+ }
+ }
+
+ if ( RotorCmd != -1 && RotorCmd != lastRotorCmd )
+ {
+ eSecCommand::pair compare;
+ compare.voltage = iDVBFrontend::voltageOff;
+ compare.steps = +4;
+ // the next is a check if voltage is switched off.. then we first set a voltage :)
+ // else we set voltage after all diseqc stuff..
+ sec_sequence.push_back( eSecCommand(eSecCommand::IF_NOT_VOLTAGE_GOTO, compare) );
+
+ // TODO .. add handling for turning rotor without measure inputpower
+ sec_sequence.push_back( eSecCommand(eSecCommand::SET_VOLTAGE, VOLTAGE(18)) );
+ // voltage was disabled..so we wait a longer time ..
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 500) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::GOTO, +7) ); // no need to send stop rotor cmd
+
+ if (send_mask)
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 750) ); // wait 750ms after send switch cmd
+ else
+ sec_sequence.push_back( eSecCommand(eSecCommand::GOTO, +1) );
+
+ eDVBDiseqcCommand diseqc;
+ diseqc.len = 3;
+ diseqc.data[0] = 0xE0;
+ diseqc.data[1] = 0x31; // positioner
+ diseqc.data[2] = 0x60; // stop
+ sec_sequence.push_back( eSecCommand(eSecCommand::IF_ROTORPOS_VALID_GOTO, +5) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SEND_DISEQC, diseqc) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 50) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SEND_DISEQC, diseqc) );
+ // wait 300msec after send rotor stop cmd
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 300) );
+
+ diseqc.data[0] = 0xE0;
+ diseqc.data[1] = 0x31; // positioner
+ if ( useGotoXX )
+ {
+ diseqc.len = 5;
+ diseqc.data[2] = 0x6E; // drive to angular position
+ diseqc.data[3] = ((RotorCmd & 0xFF00) / 0x100);
+ diseqc.data[4] = RotorCmd & 0xFF;
+ }
+ else
+ {
+ diseqc.len = 4;
+ diseqc.data[2] = 0x6B; // goto stored sat position
+ diseqc.data[3] = RotorCmd;
+ diseqc.data[4] = 0x00;
+ }
+
+ if ( rotor_param.m_inputpower_parameters.m_use )
+ { // use measure rotor input power to detect rotor state
+ eSecCommand::rotor cmd;
+ eSecCommand::pair compare;
+ compare.voltage = VOLTAGE(18);
+ compare.steps = +2;
+ sec_sequence.push_back( eSecCommand(eSecCommand::IF_VOLTAGE_GOTO, compare) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SET_VOLTAGE, compare.voltage) );
// measure idle power values
- sec_sequence.push_back( eSecCommand(eSecCommand::IF_IDLE_INPUTPOWER_AVAIL_GOTO, +8) ); // already measured?
- sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 50) ); // wait 50msec after voltage change
- sec_sequence.push_back( eSecCommand(eSecCommand::MEASURE_IDLE_INPUTPOWER, 0) );
- sec_sequence.push_back( eSecCommand(eSecCommand::SET_VOLTAGE, VOLTAGE(18)) );
- sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 100) ); // wait 100msec before measure
- sec_sequence.push_back( eSecCommand(eSecCommand::MEASURE_IDLE_INPUTPOWER, 1) );
- sec_sequence.push_back( eSecCommand(eSecCommand::SET_VOLTAGE, VOLTAGE(13)) ); // back to lower voltage
- sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 50) ); // wait 50msec
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 200) ); // wait 200msec after voltage change
+ sec_sequence.push_back( eSecCommand(eSecCommand::MEASURE_IDLE_INPUTPOWER, 1) );
+ compare.voltage = 1;
+ compare.steps = -2;
+ sec_sequence.push_back( eSecCommand(eSecCommand::IF_MEASURE_IDLE_WAS_NOT_OK_GOTO, compare) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SET_VOLTAGE, VOLTAGE(13)) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 200) ); // wait 200msec before measure
+ sec_sequence.push_back( eSecCommand(eSecCommand::MEASURE_IDLE_INPUTPOWER, 0) );
+ compare.voltage = 0;
+ sec_sequence.push_back( eSecCommand(eSecCommand::IF_MEASURE_IDLE_WAS_NOT_OK_GOTO, compare) );
////////////////////////////
- sec_sequence.push_back( eSecCommand(eSecCommand::SET_POWER_LIMITING_MODE, eSecCommand::modeStatic) );
- sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 50) ); // wait 50msec after voltage change
- sec_sequence.push_back( eSecCommand(eSecCommand::SEND_DISEQC, diseqc) );
- sec_sequence.push_back( eSecCommand(eSecCommand::SET_TIMEOUT, 40) ); // 2 seconds rotor start timout
+ sec_sequence.push_back( eSecCommand(eSecCommand::SET_POWER_LIMITING_MODE, eSecCommand::modeStatic) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SET_ROTOR_DISEQC_RETRYS, 2) ); // 2 retries
+ sec_sequence.push_back( eSecCommand(eSecCommand::INVALIDATE_CURRENT_ROTORPARMS) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SEND_DISEQC, diseqc) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SET_TIMEOUT, 40) ); // 2 seconds rotor start timout
// rotor start loop
- sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 50) ); // 50msec delay
- sec_sequence.push_back( eSecCommand(eSecCommand::MEASURE_RUNNING_INPUTPOWER) );
- cmd.direction=1; // check for running rotor
- cmd.deltaA=rotor_param.m_inputpower_parameters.m_delta;
- cmd.steps=+3;
- cmd.okcount=0;
- sec_sequence.push_back( eSecCommand(eSecCommand::IF_INPUTPOWER_DELTA_GOTO, cmd ) ); // check if rotor has started
- sec_sequence.push_back( eSecCommand(eSecCommand::IF_TIMEOUT_GOTO, +9 ) ); // timeout .. we assume now the rotor is already at the correct position
- sec_sequence.push_back( eSecCommand(eSecCommand::GOTO, -4) ); // goto loop start
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 50) ); // 50msec delay
+ sec_sequence.push_back( eSecCommand(eSecCommand::MEASURE_RUNNING_INPUTPOWER) );
+ cmd.direction=1; // check for running rotor
+ cmd.deltaA=rotor_param.m_inputpower_parameters.m_delta;
+ cmd.steps=+5;
+ cmd.okcount=0;
+ sec_sequence.push_back( eSecCommand(eSecCommand::IF_INPUTPOWER_DELTA_GOTO, cmd ) ); // check if rotor has started
+ sec_sequence.push_back( eSecCommand(eSecCommand::IF_TIMEOUT_GOTO, +2 ) ); // timeout .. we assume now the rotor is already at the correct position
+ sec_sequence.push_back( eSecCommand(eSecCommand::GOTO, -4) ); // goto loop start
+ sec_sequence.push_back( eSecCommand(eSecCommand::IF_NO_MORE_ROTOR_DISEQC_RETRYS_GOTO, +9 ) ); // timeout .. we assume now the rotor is already at the correct position
+ sec_sequence.push_back( eSecCommand(eSecCommand::GOTO, -8) ); // goto loop start
////////////////////
- sec_sequence.push_back( eSecCommand(eSecCommand::SET_TIMEOUT, 2400) ); // 2 minutes running timeout
- sec_sequence.push_back( eSecCommand(eSecCommand::SET_VOLTAGE, VOLTAGE(18)) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SET_TIMEOUT, 2400) ); // 2 minutes running timeout
+ sec_sequence.push_back( eSecCommand(eSecCommand::SET_VOLTAGE, VOLTAGE(18)) );
// rotor running loop
- sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 50) ); // wait 50msec
- sec_sequence.push_back( eSecCommand(eSecCommand::MEASURE_RUNNING_INPUTPOWER) );
- cmd.direction=0; // check for stopped rotor
- cmd.steps=+3;
- sec_sequence.push_back( eSecCommand(eSecCommand::IF_INPUTPOWER_DELTA_GOTO, cmd ) );
- sec_sequence.push_back( eSecCommand(eSecCommand::IF_TIMEOUT_GOTO, +3 ) ); // timeout ? this should never happen
- sec_sequence.push_back( eSecCommand(eSecCommand::GOTO, -4) ); // running loop start
+ sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 50) ); // wait 50msec
+ sec_sequence.push_back( eSecCommand(eSecCommand::MEASURE_RUNNING_INPUTPOWER) );
+ cmd.direction=0; // check for stopped rotor
+ cmd.steps=+3;
+ sec_sequence.push_back( eSecCommand(eSecCommand::IF_INPUTPOWER_DELTA_GOTO, cmd ) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::IF_TIMEOUT_GOTO, +3 ) ); // timeout ? this should never happen
+ sec_sequence.push_back( eSecCommand(eSecCommand::GOTO, -4) ); // running loop start
/////////////////////
- sec_sequence.push_back( eSecCommand(eSecCommand::UPDATE_CURRENT_ROTORPARAMS) );
- sec_sequence.push_back( eSecCommand(eSecCommand::SET_POWER_LIMITING_MODE, eSecCommand::modeDynamic) );
- frontend.setData(3, RotorCmd);
- frontend.setData(4, sat.orbital_position);
- }
- else
- eFatal("rotor turning without inputpowermeasure not implemented yet");
- }
+ sec_sequence.push_back( eSecCommand(eSecCommand::UPDATE_CURRENT_ROTORPARAMS) );
+ sec_sequence.push_back( eSecCommand(eSecCommand::SET_POWER_LIMITING_MODE, eSecCommand::modeDynamic) );
+ frontend.setData(3, RotorCmd);
+ frontend.setData(4, sat.orbital_position);
}
+ else
+ eFatal("rotor turning without inputpowermeasure not implemented yet");
}
}
else
git.cweiske.de / enigma2.git / blobdiff