{
int begin = turn_speed >> 16; // high word is start time
int end = turn_speed&0xFFFF; // low word is end time
{
int begin = turn_speed >> 16; // high word is start time
int end = turn_speed&0xFFFF; // low word is end time
tm nowTime;
localtime_r(&now_time, &nowTime);
int now = (nowTime.tm_hour + 1) * 60 + nowTime.tm_min + 1;
tm nowTime;
localtime_r(&now_time, &nowTime);
int now = (nowTime.tm_hour + 1) * 60 + nowTime.tm_min + 1;
-RESULT eDVBSatelliteEquipmentControl::prepare(iDVBFrontend &frontend, FRONTENDPARAMETERS &parm, const eDVBFrontendParametersSatellite &sat, int slot_id)
+RESULT eDVBSatelliteEquipmentControl::prepare(iDVBFrontend &frontend, FRONTENDPARAMETERS &parm, const eDVBFrontendParametersSatellite &sat, int slot_id, unsigned int tunetimeout)
sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, m_params[DELAY_BETWEEN_SWITCH_AND_MOTOR_CMD]) ); // wait 700ms when diseqc changed
eDVBDiseqcCommand diseqc;
sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, m_params[DELAY_BETWEEN_SWITCH_AND_MOTOR_CMD]) ); // wait 700ms when diseqc changed
eDVBDiseqcCommand diseqc;
if ( rotor_param.m_inputpower_parameters.m_use )
{ // use measure rotor input power to detect rotor state
if ( rotor_param.m_inputpower_parameters.m_use )
{ // use measure rotor input power to detect rotor state
sec_sequence.push_back( eSecCommand(eSecCommand::IF_INPUTPOWER_DELTA_GOTO, cmd ) ); // check if rotor has started
sec_sequence.push_back( eSecCommand(eSecCommand::IF_TIMEOUT_GOTO, +2 ) ); // timeout .. we assume now the rotor is already at the correct position
sec_sequence.push_back( eSecCommand(eSecCommand::GOTO, -4) ); // goto loop start
sec_sequence.push_back( eSecCommand(eSecCommand::IF_INPUTPOWER_DELTA_GOTO, cmd ) ); // check if rotor has started
sec_sequence.push_back( eSecCommand(eSecCommand::IF_TIMEOUT_GOTO, +2 ) ); // timeout .. we assume now the rotor is already at the correct position
sec_sequence.push_back( eSecCommand(eSecCommand::GOTO, -4) ); // goto loop start
sec_sequence.push_back( eSecCommand(eSecCommand::SET_VOLTAGE, VOLTAGE(18)) );
sec_sequence.push_back( eSecCommand(eSecCommand::SET_TIMEOUT, m_params[MOTOR_RUNNING_TIMEOUT]*20) ); // 2 minutes running timeout
// rotor running loop
sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 50) ); // wait 50msec
sec_sequence.push_back( eSecCommand(eSecCommand::MEASURE_RUNNING_INPUTPOWER) );
cmd.direction=0; // check for stopped rotor
sec_sequence.push_back( eSecCommand(eSecCommand::SET_VOLTAGE, VOLTAGE(18)) );
sec_sequence.push_back( eSecCommand(eSecCommand::SET_TIMEOUT, m_params[MOTOR_RUNNING_TIMEOUT]*20) ); // 2 minutes running timeout
// rotor running loop
sec_sequence.push_back( eSecCommand(eSecCommand::SLEEP, 50) ); // wait 50msec
sec_sequence.push_back( eSecCommand(eSecCommand::MEASURE_RUNNING_INPUTPOWER) );
cmd.direction=0; // check for stopped rotor
sec_sequence.push_back( eSecCommand(eSecCommand::GOTO, -4) ); // running loop start
/////////////////////
sec_sequence.push_back( eSecCommand(eSecCommand::UPDATE_CURRENT_ROTORPARAMS) );
sec_sequence.push_back( eSecCommand(eSecCommand::GOTO, -4) ); // running loop start
/////////////////////
sec_sequence.push_back( eSecCommand(eSecCommand::UPDATE_CURRENT_ROTORPARAMS) );
sec_sequence.push_back( eSecCommand(eSecCommand::SET_FRONTEND) );
}
frontend.setSecSequence(sec_sequence);
sec_sequence.push_back( eSecCommand(eSecCommand::SET_FRONTEND) );
}
frontend.setSecSequence(sec_sequence);