| Age | Commit message (Collapse) | Author | |
|---|---|---|---|
| 2009-01-19 | remove nested structures because of the fact that swig cannot handle this | ghost | |
| now we no more need the bad duplicate definitions of eDVBFrontendParametersSatellite/Cables/Terrestrial content i.e. eDVBFrontendParametersSatellite.System_DVB_S or eDVBFrontendParametersSatellite.FEC_Auto.... | |||
| 2009-01-19 | add unicable support (thx to adenin) | ghost | |
| 2008-12-19 | small fix | ghost | |
| 2008-12-19 | initialize lnb config | ghost | |
| 2008-12-13 | add possibility to set manual lnb priority (only in advanced sat config) | ghost | |
| range 0..64 to decrease priorities (this is lower as all auto given priorities) range 14000..14064 this is higher than auto given rotor priorities range 19000..19064 this is higher than each auto given priorities | |||
| 2008-12-03 | hopefully finally fix "second cable of motorized LNB" | ghost | |
| 2008-12-03 | dont switch to 18V and measure input current, when slow rotor tuning is selected | ghost | |
| 2008-11-25 | add possibility to always switch to 13V before do sec commands | ghost | |
| 2008-11-13 | add possibility to change delay after diseqc reset command and delay after ↵ | ghost | |
| diseqc peripherial poweron command via satellite equipment control plugin | |||
| 2008-11-12 | enable static limiting mode before every sec change | ghost | |
| 2008-11-06 | Add DiSEqC reset after voltage enable and tune failed... hopefully this ↵ | ghost | |
| fixes problems with some DiSEqC switches | |||
| 2008-10-24 | small fixes for loopthrough | Andreas Monzner | |
| 2008-10-14 | fix typo | Andreas Monzner | |
| 2008-10-14 | fix incorrect calculated score when loopthrough to a motorized lnb | Andreas Monzner | |
| 2008-10-09 | add delay before send sequence repeat (diseqc/toneburst) | Andreas Monzner | |
| 2008-10-03 | add code to simulate recordings (with faked frontends) | Andreas Monzner | |
| now its more easy to build a timer overlap detection or similar | |||
| 2008-09-30 | fix non working "2nd lnb from motorized dish" | Andreas Monzner | |
| 2008-09-08 | replace eFatal (which can occour during servicescan at some conditions) with | Andreas Monzner | |
| a debug message | |||
| 2008-09-06 | allow more complicated sat configuration | Andreas Monzner | |
| 2008-09-05 | set static powerlimiting every time when diseqc is sent | Andreas Monzner | |
| 2008-08-28 | revert local change | Andreas Monzner | |
| 2008-08-28 | fix tune failed problems on fast zap | Andreas Monzner | |
| 2008-08-18 | rotor turing without power measure fixes | Andreas Monzner | |
| 2008-08-08 | fix tonemode setting | Andreas Monzner | |
| 2008-08-04 | improove motor turning without power measure | Andreas Monzner | |
| 2008-08-04 | fix tune failed problems on fast zap when a diseqc swicth is in use | Andreas Monzner | |
| 2008-07-24 | optimize linked tuner handling | Andreas Monzner | |
| 2008-07-19 | now link dvb-s frontends to dvb-s2 frontends is possible | Andreas Monzner | |
| 2008-07-19 | remove no more needed function | Andreas Monzner | |
| 2008-07-17 | fix linking tuners | Andreas Monzner | |
| 2008-06-26 | fix rotor turning with power measure | Andreas Monzner | |
| 2008-05-19 | remove no more needed time code | Andreas Monzner | |
| 2008-04-28 | make final tune timeout symbolrate depending | Felix Domke | |
| 2008-03-25 | fix: diseqc.eDVBDiseqcCommand::data[n] is used uninitialized in this function | Andreas Oberritter | |
| 2008-03-25 | change get/setData to use long instead of int, to match pointer size on all ↵ | Andreas Oberritter | |
| systems | |||
| 2008-03-20 | add support for dm8000 onboard tuner linking | Andreas Monzner | |
| 2007-07-07 | add possibility to set rotor turning speed to fast/slow or set a time epoch | Andreas Monzner | |
| for turning fast add some missing and new translations | |||
| 2007-07-07 | add some debug output | Andreas Monzner | |
| 2007-07-07 | hold the lnbp overcurrent detection at static detection until the rotor has | Andreas Monzner | |
| stopped... this gives a little bit more power resources to turn the rotor (needed when the lnb self has a high power consumption) | |||
| 2007-07-02 | set voltage before send diseqc command (like DiSEqC spec) | Andreas Monzner | |
| 2007-06-08 | hopefully fix "secondary cable from motorized tuner" setting | Andreas Monzner | |
| some code cleanups now link tuners in all directions should be possible | |||
| 2007-06-06 | some fixes for empty tuner slots (use slotid instead of dvb api frontend | Andreas Monzner | |
| device id) replace some hacks with some better hacks ;) | |||
| 2007-02-14 | make retransmit rotor diseqc command retries changable | Andreas Monzner | |
| 2007-02-14 | make some diseqc / continuous tone / toneburst / rotor values (delays, | Andreas Monzner | |
| timeouts) configurable via /etc/enigma2 for name of the config entries look at lib/python/Components/NimManager.py in InitSecParams function TODO: build a simple Plugin to change this values via gui (with a description for each value) Hopefully now we can get rid of the "Tune failed" or other messages with some diseqc switches | |||
| 2006-12-26 | small rotor diseqc fix | Andreas Monzner | |
| 2006-12-05 | small optimize | Andreas Monzner | |
| 2006-11-30 | some changes for service groups | Andreas Monzner | |
| 2006-11-25 | python object refcount debugging code second try | Andreas Monzner | |
| 2006-06-29 | better readable code | Andreas Monzner | |
| 2006-06-29 | much longer delay between committed and uncommitted diseqc command | Andreas Monzner | |
 |
index : enigma2.git | |
| Clone of git://git.opendreambox.org/git/enigma2.git before dream multimedia removed all the engima2 sources |
| aboutsummaryrefslogtreecommitdiff |