aboutsummaryrefslogtreecommitdiff
path: root/lib/dvb/sec.cpp
AgeCommit message (Expand)Author
2009-10-28fix rotor tuning symbolghost
2009-09-10sec.cpp: more bcm4506 supportghost
2009-08-12much better motor turning without possibility of power measurementghost
2009-07-06more prio for linked and satpos dependent tuners when the base tuner is in useghost
2009-04-07sec.cpp: make "second cable from rotor lnb" working againghost
2009-03-28sec.cpp: let static limiting mode enabled for 500 msec after tuneghost
2009-03-28ignore all non diseqc 1.2 lnbs for satpos dependent tunersghost
2009-03-27sec.cpp: fix a linked tuner problem, c++ changes to support link tuners to 2n...ghost
2009-02-25unicable fix by adenin (when Kathrein ESU33 is used)ghost
2009-02-20split "delay after continuous tone" value in "delay after continuous tone dis...ghost
2009-01-19remove nested structures because of the fact that swig cannot handle thisghost
2009-01-19add unicable support (thx to adenin)ghost
2008-12-19small fixghost
2008-12-19initialize lnb configghost
2008-12-13add possibility to set manual lnb priority (only in advanced sat config)ghost
2008-12-03hopefully finally fix "second cable of motorized LNB"ghost
2008-12-03dont switch to 18V and measure input current, when slow rotor tuning is selectedghost
2008-11-25add possibility to always switch to 13V before do sec commandsghost
2008-11-13add possibility to change delay after diseqc reset command and delay after di...ghost
2008-11-12enable static limiting mode before every sec changeghost
2008-11-06Add DiSEqC reset after voltage enable and tune failed... hopefully this fixes...ghost
2008-10-24small fixes for loopthroughAndreas Monzner
2008-10-14fix typoAndreas Monzner
2008-10-14fix incorrect calculated score when loopthrough to a motorized lnbAndreas Monzner
2008-10-09add delay before send sequence repeat (diseqc/toneburst)Andreas Monzner
2008-10-03add code to simulate recordings (with faked frontends)Andreas Monzner
2008-09-30fix non working "2nd lnb from motorized dish"Andreas Monzner
2008-09-08replace eFatal (which can occour during servicescan at some conditions) withAndreas Monzner
2008-09-06allow more complicated sat configurationAndreas Monzner
2008-09-05set static powerlimiting every time when diseqc is sentAndreas Monzner
2008-08-28revert local changeAndreas Monzner
2008-08-28fix tune failed problems on fast zapAndreas Monzner
2008-08-18rotor turing without power measure fixesAndreas Monzner
2008-08-08fix tonemode settingAndreas Monzner
2008-08-04improove motor turning without power measureAndreas Monzner
2008-08-04fix tune failed problems on fast zap when a diseqc swicth is in useAndreas Monzner
2008-07-24optimize linked tuner handlingAndreas Monzner
2008-07-19now link dvb-s frontends to dvb-s2 frontends is possibleAndreas Monzner
2008-07-19remove no more needed functionAndreas Monzner
2008-07-17fix linking tunersAndreas Monzner
2008-06-26fix rotor turning with power measureAndreas Monzner
2008-05-19remove no more needed time codeAndreas Monzner
2008-04-28make final tune timeout symbolrate dependingFelix Domke
2008-03-25fix: diseqc.eDVBDiseqcCommand::data[n] is used uninitialized in this functionAndreas Oberritter
2008-03-25change get/setData to use long instead of int, to match pointer size on all s...Andreas Oberritter
2008-03-20add support for dm8000 onboard tuner linkingAndreas Monzner
2007-07-07add possibility to set rotor turning speed to fast/slow or set a time epochAndreas Monzner
2007-07-07add some debug outputAndreas Monzner
2007-07-07hold the lnbp overcurrent detection at static detection until the rotor hasAndreas Monzner
2007-07-02set voltage before send diseqc command (like DiSEqC spec)Andreas Monzner
generated by cgit v1.2.3 (git 2.46.0) at 2026-01-19 02:33:05 +0000